Aritech

Tecom Challenger 4Door NAC - Network Access Controller With Dual Wiegand Interface - Kit With Enclosure The Network Access Controller is an access ...

The stylish Aritech AI673 optical/acoustic alarm indicators have been designed for use with most types of automatic and non-automatic alarm detecto...

The VV600 Plus seismic detector is designed to detect attempts to break into vaults and safes. This seismic detector reacts to the characteristic v...

The DD669AM is a dual technology ceiling mount motion sensor with anti-masking. It will prevent attempts to mask the sensor while reporting these a...

The VV602 seismic detector is designed to detect attempts to break into night deposit boxes, automatic teller machines (ATM?s) and other reinforced...

Accessories for seismic detectors. When mounting the seismic detectors on concrete you should always use the VM600P mounting plate.

A linear power supply used to supply power to remote products at 13.8 Volts DC. Enclosed in a metal box with room for a 6.5AH battery & tamper ...

The CA111x series of keypads combines advanced remote arming station and keypad functionality, smart card reader (CA1115 and CA1116 only), ease of ...

The keypad may be connected directly to the Challenger RS-485 LAN, up to 1.5 km from the Challenger panel or Intelligent Access Controller. It has ...

TS082x series of data gathering panels (DGPs) are used to expand the number of inputs and outputs (or relays) on the Challenger system. DGPs allow ...

The 4 LED Arming Station was designed to be flush or surface mounted, with a sturdy plastic cover & hard-wearing buttons. Four LED's indicate a...

The CA111x series of keypads combines advanced remote arming station and keypad functionality, smart card reader (CA1115 and CA1116 only), ease of ...

The CA111x series of keypads combines advanced remote arming station and keypad functionality, smart card reader (CA1115 and CA1116 only), ease of ...

Relay boards are connected to a ten-way plug on the Challenger, Access Controllers, or DGP's to expand relay capacity. The TS0840 provides an addit...

Tecom Challenger 4Door NAC - Network Access Controller - PCB Only The Network Access Controller is an access control solution allowing you to manag...

Tecom Challenger 4Door NAC - Network Access Controller - With Enclosure The Network Access Controller is an access control solution allowing you to...

The TS0801 Arming station is one of the most widely recognised keypads in Australia and New Zealand. It is easy to install and has been the face of...

The 8-input expansion module adds eight inputs to the Tecom range of Data Gathering Panels (DGPs). This provides an inexpensive way to increase the...

The Network Access Controller is an access control solution allowing you to manage your door and access requirements as well as supporting intrusio...

The Dual Wiegand Interface is a module which allows Wiegand technology readers to be connected to a ChallengerPlus or Network Access Controller sys...

The Intelligent Four-Door Controller extends the Challenger system's capability to provide state-of-the-art access control functionality. Each Inte...

The Intelligent Four-Lift Controller extends the Challenger system's capability to provide state-of-the-art lift access control functionality. Each...

Tecom Challenger Firmware Chip - V8 Main Control Panel (TS0816)

The TS0006 is an access control keypad for the Challenger Control Panel. Typically used to authenticate user access to a door, the keypad can easil...

Inovonics TS0825E Wireless Data Gathering Panel (WDGP) Provides cable-free installation of devices to your Challenger system such as PIRs, smoke d...

Save time and money installing Challenger with the new TS0098 Challenger IP LAN Adaptor. TS0098 modules allow Challenger RS-485 LAN data to be carr...

The Challenger system utilises a special derivative of RS485 for LAN communication. On occasions there may be a need to electrically isolate signal...

Multipurpose enclosure can be used for Tecom control boards and accessories.

The Network Access Controller is an access control solution allowing you to manage your door and access requirements as well as supporting intrusio...

The Power Distribution Board provides a simple means of star connecting Challenger LAN devices. Fitted with a single protected input port and five ...

This unit converts the Challenger LAN to Optical Fibre. One or two optical fibre connections can be used with this interface. When using one optica...

The TS0862 Smart Door Controller is a low cost, compact door controller that performs all the functions necessary to control the operation of a sin...

Small metal enclosure for the Challenger series of control panels.

Tecom Clamshell Smartcard is the secure, convenient credential for the Tecom Smartcard Reader system.

Tecom Smart Card E-CoilMinimum Order Quantity -10

Tecom Challenger Smart Card - Fob

Tecom Challenger Smart Card - ISO

Tecom Challenger Smart Card - Silicon Wrist Band

The TS0870 series of Smart Card Readers provide secure authentication of users to the Challenger system for intrusion detection and access control....

The TS0870 series of Smart Card Readers provide secure authentication of users to the Challenger system for intrusion detection and access control....

The TS0870 series of Smart Card Readers provide secure authentication of users to the Challenger system for intrusion detection and access control....

The TS0870 series of Smart Card Readers provide secure authentication of users to the Challenger system for intrusion detection and access control....

The TS0870 series of Smart Card Readers provide secure authentication of users to the Challenger system for intrusion detection and access control....

The Touch Screen Remote Arming Station (RAS) builds on the continued success of the Tecom portfolio for Challenger control panels. The Touch Screen...

Universal metal enclosure for the Challenger series of control panels.

The 4G Communication Module is an expansion module which allows Challenger panels to communicate over 4G wireless networks. The 4G Communication Mo...

TS1020 Analogue Data Gathering Panels (DGPs) are used to expand the number of inputs and outputs (or relays) on the Challenger system. It brings br...